Menu
Download 1085 Yamaha Outboard Motor PDF manuals. User manuals, Yamaha Outboard Motor Operating guides and Service manuals. Tachometer unit NOTE: Depending on the model of the outboard motor, some functions may not be compatible. For information on models which contain the compatible functions, consult a Yamaha dealer. Tachometer The tachometer shows the engine revolutions per minute. (Page 3) Trim meter The trim meter shows the trim angle of the outboard motor.
Sections:
Repair Difficulty:Easy
PREFACE
This flush mount, alternator tachometer is designed for use on the following:
- Johnson® and Evinrude® Outboards
- OMC Sea Drive® Models Pivot stickfigure animator 5.
- NON-BRP products with 20 pole alternators
Installation
Disconnect battery cables to help prevent arcing or damage to equipment.
Select a tachometer mounting location that is in full view of the operator.
Drill a 3-3/8 in. (86mm) hole in the dashboard.
Yamaha Outboard Digital Tachometer Manual
Mount the tachometer so water will not collect on the face, or drip on the case and wires. https://nqx-is-cats-download-underground-mac-os-hell.peatix.com. If the tachometer is covered by a transparent shield, the shield must be adequately ventilated to help prevent sunlight heat soak damage.
Set Pulse Selector Switch
[1]
Align the arrow on the PUL/REV (pulses-per-revolution) switch (A) with the appropriate number.
Align the arrow on the PUL/REV (pulses-per-revolution) switch (A) with the appropriate number.
- Edirol da 2496 windows 7 drivers. Engines with two yellow stator wires (yellow and yellow/gray) set switch to '6'
- Engines with three yellow stator wires (yellow, yellow/gray and yellow/blue) set switch to '5'
- NON-BRP engines with 20 pole charging system, set switch to '3'
1968 THRU 1972 Outboards
If you are replacing an older Battery CD Ignition tachometer, or if the engine has never had a tachometer, move the engine harness gray wire to the rectifier yellow/gray circuit on the terminal board.
1978 and Newer Outboard and OMC Sea Drive
Yamaha Outboard Tachometer Manual
Use a wiring kit to connect the tachometer to the plug-in connector on the remote control or accessory electrical cable.
- Use Plug-In Connector Kit P/N 0174732 when installing tachometer only. Mr. fast mac os.
- Use Plug-In/Fuse Block Kit P/N 0173611 when installing tachometer with other accessories.
All Models
Use No. Wintrack full version. 8 insulated ring terminals and No. 16 A.W.G. wire of the specified color.
[1]
HELPFUL HINT: install star washer, ring terminal, and nut - in that order. This will help prevent ring terminal from rotating and loosening the nut. Connect all wires before installing gauge in dashboard.
HELPFUL HINT: install star washer, ring terminal, and nut - in that order. This will help prevent ring terminal from rotating and loosening the nut. Connect all wires before installing gauge in dashboard.
[1]
Connect the following:
Connect the following:
(B) To dashboard light switch, DARK BLUE WIRE.
Yamaha Outboard Tachometer Manual
(C) To alternator, GRAY WIRE.
(D) To ground connection, BLACK WIRE.
Rarbg photoshop cs6. (E) To key switch accessory terminal, PURPLE WIRE.
Insert the gauge into dashboard. Install bracket, star washers, and mounting nuts.
Do not overtighten the mounting nuts as you could permanently damage the gauge. https://bestvload843.weebly.com/foxback-mac-os.html.
Yamaha Outboard Tachometer Problems
Connect battery cables. Test the tachometer operation by running the engine.
Important: Multiple battery installations require a common battery ground cable. Refer to Outboard Installation Guidelines P/N 0508167.
Yamaha Outboard Tachometer Gauge
[1]
To replace the light bulb, pry out light socket cover (F). Turn bulb socket counter-clockwise and pull out. Replace with a No. 194 bulb, P/N 0125432.
To replace the light bulb, pry out light socket cover (F). Turn bulb socket counter-clockwise and pull out. Replace with a No. 194 bulb, P/N 0125432.